Ask the A&Ps

The definitive guide to owner maintenance, slipping starter adapters, and close CHT tolerances.

Email [email protected] for a chance to get on the show.

Join the world's largest aviation community at aopa.org/join

Creative leaning techniques, rusty cylinders, and odd manifold pressure indications are on tap this time.

Send your questions to [email protected] for a chance to get on the show.

Join the world's largest aviation community at aopa.org/join

Old engines, rusty airplanes, and a strange valve incident are the puzzlers for Mike, Paul, and Colleen this episode. Send your questions to [email protected] for a chance to get on the show.

Join the world's largest aviation community at aopa.org/join

Full episode notes below:

John has a Beech Musketeer who had an unusual situation with his valve. The valve seat separated from the cylinder barrel and dropped down, striking the piston crown. He's wondering if he did anything to cause this, despite never exceeding 425 degrees CHT. The hosts agree that it was probably a manufacturing error, even though the cylinder had a few hundred hours on it. Mike said the only way this can happen is with a manufacturing problem or a high heat event.

Larry has an early SR22 with 3,300 hours on the engine. It's not in need of an overhaul now, but Larry has read those early SR22 cases are more robust, and he's wondering when the time comes if he should overhaul or do a factory reman. The hosts aren't aware of any particular issues that make cases from that generation better, but they do offer some sound advice on the reman versus overhaul question. Mike said that if the engine has been treating him well that Larry should overhaul it. And if it's been a lemon, send it off and get a new one from the factory. Larry is a little worried about resale, since people are skiddish with high-time engines. Mike suggests that an airplane with run-out engines is the best investment because it's been fully depreciated. Any additional time is essentially free.

Terry has been looking for a 182 and he saw one in California with corrosion. He wonders how much corrosion is too much. Paul said that according to Terry's photos, he wouldn't think twice about buying the airplane. The general rule is that you can take off only 10 percent of a structure and not worry about it. The skin on top of the wing where the corrosion can be seen is only 25 thousandth of an inch, which means you could only take off 2.5 thousandth of an inch and still use that skin. White splotching can be seen in the photos, and Paul said it's common for airplanes of that vintage, and not to repair it. Instead, he recommends spraying it with ACF-50 or Corrosion-X every few years. Doing so will stop the spread and not allow any further damage.

Pre-emptive engine overhauls, upgrading an old electrical system, spark plug anti-seize, and old wood wing concerns are on tap for this episode.

Send your questions to [email protected] for a chance to get on the show.

Join the world's largest aviation community at aopa.org/join

Full episode notes below:

Lance inherited some furniture that had lived in the Midwest for 200 years, and began splitting after only a few years after he moved to Salt Lake City. He's wondering if the same concern would hold with wood wings, like those on the Bellanca Viking. The hosts say not to worry. The wood spars are lathered with a varnish that helps keep out moisture, Sitka spruce is resistant to splitting, and Mike said in his experience with Vikings in the 1970s, shops didn't report issues with airplanes that had lived in different parts of the country.

Jim has an Arrow and he wants to guard against the long down times we're seeing at overhaul shops. To do so he wonders if she would pick the right time and pre-emptively overhaul his engine, or at least change out the cylinders. Mike, Paul, and Colleen fully lecture poor Jim on the perils of so-called top overhauls, and instead advise him to do nothing more than stock a cylinder in case the time comes and he needs it.

Darren is thinking of putting an all-new panel into his Tri-Pacer, and he's wondering if he should upgrade his generator to an alternator when he does it. Paul said he's not worried about the generator when it comes to his avionics, but given that Darren flies at night, Paul thinks an alternator is probably a good idea.

Steve is wondering about spark plug anti-seize compounds. He uses the Tempest and Champion products, but found Lycoming's service instructions that prohibits their use. It calls for a copper-based compound, or motor oil. The hosts think the guidance might be a result of getting the carbon-based anti-seize on the insulator, which would cause arcing. They all agree that motor oil would be a bad choice. Paul thinks the Champion compound is fine, so long as you use only a little, and keep it off the last thread. Mike now uses an anti-seize stick that you apply to the threads, almost like a lip balm.

A creative modification, lean of peak with turbocharging, electronic ignition, and oil leaks are on tap. Email [email protected] for a chance to get on the show.

Join the world's largest aviation community at aopa.org/join

Full notes below:

Tom has a turbocharged Mooney and he's wondering how to manage it while lean of peak. The hosts say the first goal is to get on the lean side quickly, and then fine tune once there. They argue you can hear and feel when you're lean of peak, which is how you can expedite it. Then check the CHTs and the TITs to make sure they are below limits. That's it. Paul said in that way turbos have an advantage because it doesn't at what altitude you lean, the numbers should be similar. He tends to lean based solely on fuel flow.

Ray is considering going to dual electronic magnetos, but he's concerned about redundancy and the safety of the associated battery. The hosts talk at length about the benefits of dual e-mags, and think that redundancy is better with e-mags than traditional magnetos, so even though you're going away from two independent systems, it's still an improvement. Mike said the TSO for the battery containment is extremely high, and not to worry about thermal runaway. The company must also think so because apparently the experimental version is largely the same, minus the same battery containment.

Eric is a new A&P and he's trying to become better informed on the difference between major and minor overhaul. He helped a friend create an external charging port for a battery minder on the belly through an inspection port. The hosts are wowed by the work, and want to do it themselves, and all agree it's a minor alteration. It doesn't stick out into the airflow any more than a GPS antenna, which is a minor alteration. Mike recommends reading FAR Part 1.1, which gives the definition of a major alteration. If it doesn't meet that definition, it's minor. But of course Eric is a scientist by day and doesn't love the ambiguity of the reg. Mike says it's in his best judgement, and part of his role as a mechanic.

Walter is trying to track down an oil leak on his Beech Sierra. Over a few years he's had his mechanic address multiple trouble spots, and over time that's helped. But recently he's had some oil pooling on his lower cowling. Colleen thinks areas such as oil return lines are problematic. The rubber boots connecting those lines get worn out and can be replaced. She's been trying to track down an oil leak on her Lycoming without luck, and gives Walter a bunch of places to check.